With the surge in domestic car ownership, recalls due to vehicle safety hazards continue to rise. From January 1 to June 30, 2018, the AQSIQ issued a total of 88 recall notices. After collecting relevant data, Netcom found that a total of about 4.92 million vehicles were recalled, of which 2,488,223 were recalled by Japanese, accounting for 51% of the total recall. The reasons for the recall included airbags, steering assist, engine, brakes, front windshield, wiper and other issues; a total of 1,378,033 vehicles were recalled 13 times due to airbag hazards. Below we will analyze the types of recall faults and the proportion of data for each vehicle. First, the Japanese, German, and American recalls accounted for over 90% As of June 30, the total number of recalled vehicles in China was mainly Japanese, German and American brands, with a total of 88 recalls involving 16 brands. Among them, the Japanese government recalled 2,488,223 vehicles, accounting for 51% of the total recall; the German recalls totaled 1,305,179 vehicles, accounting for 27% of the total recall; the US Department recalled 639,103 vehicles, accounting for 13% of the total recall. Among the remaining cars, 330,398 self-owned brands were recalled, 107,302 were recalled by the Korean system, 50,024 were recalled by the European Department, and 3,822 were recalled by the French Department. (Note: European brands are European brands other than German and French) As of June 30, the General Administration of Quality Supervision, Inspection and Quarantine issued 88 recall notices for 20 safety hazards. Among them, the airbag hidden danger recalled 29 times, a total of 1,337,783 vehicles; the steering assisted hidden danger recalled 10 times, a total of 200,424 vehicles; engine hidden danger recall 7 times; the front windshield hidden dangers were recalled 3 times, wiper, seat belt, door lock and shifting Each recall of the box was 2 times, and the fuel leak, chassis, instrument and skylight were recalled once. 1. Japanese brand The Japanese brands recalled a total of 32 times, of which the most recalled were brakes, totaling 689,031. 2, German brand Front/rear bridge connection axis hidden danger The German brand recalled 33 times, of which the most recalled were the coolant pump hidden dangers, a total of 659,049 vehicles. 3, the US brand The US brand recalled a total of 12 times, of which the most recalled was the fatigue of the inner braid of the brake hose, a total of 567,167. 4, independent brand The self-owned brands recalled a total of six times, of which the most recalled was the increase in oil, totaling 252,087 units. 5, Korean brand The Korean brand was recalled 5 times, and the most recalled was the instrument panel fault light that was lit up and could not be started, totaling 63,852 units. 6, European brand The Korean brand has recalled 10 times, of which the most recalled engine fuel rail end caps are incomplete, totaling 26,307. 7, the law brand The legal system has been recalled three times, including one recall for each of the engine, engine hood and door lock parts. This time, the legal brand recalled a total of 3,822 vehicles.
Plastic car exterior parts refer to front and rear bumper moulds, fog lamp moulds, and grilles and all plastic accessories, are requesting high quality with hardened steel 1.2738 or Finkl P20 hard steel in order to guarantee specified mould life such as 1000000shots. Plastic injection material is PP or ABS as per customer's requirement. Ceeto company has skilled design engineering team who is able to design plastic car bumper moulds as per part geometry, bumper mould design will be first considered hidden parting line or visible parting line according to DFM analysis and moldflow report.
Technical information for Car front bumper and rear bumper mould
Ceeto Service Scope to manufacture car bumper mould
Plastic Car Front Bumper and rear bumper mould test
Before we ship bumper mould to you, we will have bumper mould buy-off in house together with you, and we must make official at least three mould tryouts and 2000 empty cycle for mould to check if mould function is ok in a certain time.
Normally, you and we attend the validation procedure together and sign off after checking. What we are checking usually are as follows:
Plastic car bumper mould material and heat treatment
What we will also inspect mould material and heart treatment as follows:
We warmly welcome you to visit us and send us RFQ, we want to be your part of suppliers and we will do our utmost efforts to make high quality of moulds and products, if you have any doubts about technical points, please don't hesitate to let us know, we are looking forward to hearing from you, thanks a lot.
Automotive Exterior Plastic Injection Mould Automotive Exterior Plastic Injection Mould,Injection Molding Automotive Parts,Plastic Car Front Bumper,Plastic Car Rear Bumper Zhejiang Ceeto Molding Technology Co.,Ltd. , https://www.ceetomold.com